How Is The Barrier Gate Ticket Recognition Installed

Step 1: Install the road gate

First of all, we need to help the gate to find a good position, then move the gate over, and start to mark the punch mark. Here, use chalk or ink pen to mark the exact position of the punch, the hole position is fine and precise, the mark is do not shake the machine, to avoid misalignment. After the punching position is marked, remove the machine and start punching after marking the punching position.

Select the matching drill bit according to the specification of the expansion screw only carried by the machine. Generally, the specification of the expansion screw is 12-14. There is no requirement for selection, as long as it is firmly fixed, and then the expansion screw is knocked in.

The slot is reserved for threading. The slot is slotted according to the direction of the line. The length and width of the slot are based on the actual situation of the site. There is no fixed position and sores for reference. As long as you think it is suitable and easy to thread. After the reserved wire slot is opened, start the installation of the fixed gate gate. Two people are required to cooperate with the operation. The gate hole is aligned with the expansion screw, slowly move the adjustment position to the hole position, and then put it into the hole position and insert the expansion screw. Cap and tighten, here must be fixed firmly and firmly tighten the screw cap.

After installing the gate gate, start to install the gate rod. Align the 4 screws on the rod, and 2 people cooperate to install the rod. Generally, the rod is relatively long between 2 meters and 6 meters. Tighten the 4 screws on the rod. , the installation of the first barrier gate is completed.

Step 2: Install ticket recognition

License plate recognition is mainly divided into 4-line license plate recognition, two-line license plate recognition, and integrated license plate recognition. Generally, there are more commonly used 4-line license plate recognition. Knowing cameras, these three are the most commonly used brands on the market, and there are two other brands, Dahua and Haikang, which are generally seldom used because they are relatively expensive and not cost-effective. Regardless of the device brand, their installation and wiring methods are almost the same, but the names of the interface labels are different. We took the 4-line screen license plate recognition and Qianyi camera as an example to learn this other similarities.

Start to assemble the license plate recognition, first assemble the license plate recognition base, tighten the 4 screws of the base, install the license plate recognition camera, install the black corrugated plastic cable, and then install the link on the body, tighten the two screws below the camera, start Connect the wires on the license plate recognition device, first install the data cable from the camera to the display screen, find a wire of about 1 meter, and pass it through the camera wire tube into the display case. The red wire is connected to the A port terminal, and the black wire is connected to the B port terminal. Unplug the terminal and use a small flat-blade screwdriver to loosen the terminal and connect it to the wire. The red wire is connected to A and the black wire is connected to B. Don't make a mistake. Then start connecting the A and B ports of the main board in the display screen, and thread the wire that has been connected to the camera into the inside the display case. Here, the red wire is also connected to the main board terminal A port, and the black wire is connected to the B port. Generally speaking, the A and B ports of the camera and the A and B ports of the display must be connected in the same order, and finally start to pass through the power cable, license plate The identified power cord is generally 3 meters long enough to get power through the gate, and then connect to the camera power supply, connect it to the back and tangle with the 220V power supply of the fill light. Note that the fill light is 12V power supply and does not need to be connected to the 22V power supply. span

Before connecting, be sure to confirm whether the power supply of the fill light is 12V or 22V. Finally, twist the license plate recognition power cable, the camera power cable, and the gate power cable together, connect them to the 22V power supply of the 12V power supply, and then connect the main power cable to the On the power supply of the gate machine, it can basically be completed!